1.Product introduction of the new high output tire wall circular cutter(tire sidewalls cutter):

Function: This new high output tire wall circular cutter(tire sidewalls cutter) is used for the decomposition and processing of used tires.This is designed to remove the tire bead ring and the tire wall on the both sides from a complete waste tire so as to facilitate the further step of the waste tire processing.

Operation flow: First, place the tire on the horizontal pallet of the new high output tire wall circular cutter(tire sidewalls cutter), and secure the waste tire firmly by locking the tensioning device. Next, start the machine, grasp the handle, push the rotating arm, and position the blade close to the top of the tire (note to adjust the upper limit screw of the column). Then, slowly lower the blade, proceed step by step, until the side wall of the tire is cut off. Finally, turn off the power, remove the tire, and complete the operation. In case of a severe tire blowout or if the exposed steel wire cannot be removed, the tire should be removed and the exposed part should be cut off using a grinding wheel cutter.

2.Product advantage of the new high output tire wall circular cutter(tire sidewalls cutter):

Horizontal pallet

*Horizontal pallet, stable operation
Place the tires horizontally on the horizontal pallet without lifting them. The horizontal pallet evenly supports the tires across entire surface of the new high output tire wall circular cutter(tire sidewalls cutter), with the weight distributed evenly across the pallet. During the process of cutting the bead, the force is balanced, resulting in a smooth cut with less risk of chipping the blade, slipping, or cutting off to the side.

*Support customization, various application Customization can be done according to customer requirements. Both small and large tires can be placed horizontally. Whether it's a small truck tire or a large truck tire, no additional fixtures are needed. Compared to the vertical type, the new high output tire wall circular cutter(tire sidewalls cutter) is less likely to encounter problems such as unstable center of gravity for large tires or difficulties in holding small tires.

*Easy operation, quick grasp When the tires are laid out horizontally, the bead (inner and outer edges) on both sides is fully exposed. The operator can clearly see the position where the blade cuts the bead by directly observing, which is convenient for fine-tuning and positioning. New comer can also easily get started.

Manual tensioning device

*Lower cost, lower failure rate
Without hydraulic or pneumatic supporting components, the new high output tire wall circular cutter(tire sidewalls cutter) eliminates the need for hydraulic cylinders, air pipes, oil pumps, and electromagnetic valves; the structure is simple, and oil leakage and air leakage faults rarely occur. The maintenance threshold is extremely low, making it suitable for small and medium-sized recycling processing plants.

*Easy operation, strong controllability
Operators can manually adjust the opening degree. They can flexibly control the tensioning force according to the size of the tires to avoid over-tensioning and damaging the old tires, and also prevent the tires from slipping due to too loose clamping.

*Stable continuous clamping
The mechanical locking structure can maintain the open state after adjustment and can continuously keep the tensioning state during cutting, preventing automatic retraction during the cutting process, and ensuring continuous cutting of the inner and outer tire rings.

Low energy consumption

The new high output tire wall circular cutter(tire sidewalls cutter) has a compact structure and reasonable power matching, reducing unnecessary energy consumption. The advantages of long-term use for small and medium-sized tire recycling processing plants are obvious.

Three-phase motor or single-phase motor (optional)

*Three-phase motor：

Strong and stable torque, powerful enough for heavy-duty truck tyres.

Low vibration & low heat generation, support long-time continuous working.

High power efficiency, lower energy loss, save electricity for mass production.

Long service life and easy maintenance.

*single-phase motor：

Works with common 220V single-phase household power supply.

No need for industrial 3-phase electricity, suitable for small workshops.

Easy installation, plug and use without extra wiring modification.

Ideal choice for small recyclers with limited power condition.

Wear-resistant cutting knives

The new high output tire wall circular cutter(tire sidewalls cutter) is equipped with hard alloy cutting knives, which have high hardness and excellent wear resistance. When cutting the composite structure of scrap tire bead wires and rubber, the cutting edge is less likely to be damaged or dull, and maintains sharpness for a long time during continuous cutting

High cost-effectiveness, cost-saving

The new high output tire wall circular cutter(tire sidewalls cutter) can be customized according to customer requirements and has a wide range of applications: car tires, truck tires, OTR tires, etc.

3.Product parameters of the new high output tire wall circular cutter(tire sidewalls cutter):

model	QKF850	QKF1150	QKF1500
motor power(kw)	2.2	2.2	4
processing range(mm)	750-1200	750-1200	1200-1500
capacity(kg/h)	2000	2000	2000
weight(kg)	500	550	750
size(mm)	*13009001480*	*152011501480*	*20201501920*